温轧温度对中碳Cr-Mo钢组织性能的影响

通过SEM、EBSD和拉伸试验研究了温轧温度对中碳Cr-Mo钢组织演变和力学性能的影响。结果表明:较高温轧温度有利于Cr-Mo钢组织的均匀分布,当轧制温度从500 ℃增加到600 ℃时,铁素体晶粒尺寸由0.424 μm增加到0.490 μm,晶粒尺寸差别不断减小,屈服强度由1380 MPa下降至1062 MPa,在550 ℃轧制试验钢的塑性最好,强塑积最高,为5816 MPa·%。     

Heat and mass transfer flow over a stretching surface with Ohmic heating and chemical reaction

The present study analyzes the effect of chemical reaction on an unsteady magnetohydrodynamic boundary layer viscous fluid over a stretching surface embedded in a porous medium with a uniform transverse magnetic field. A Darcy‐Forchheimer drag force model is employed to simulate the effect of second‐order porous resistance. Dissipative heat energy based on both viscous and Joule dissipation along with a heat source/sink is considered to enhance the energy equation. Similarity analysis is imposed to transform the governing differential equations into a set of nonlinear coupled ordinary differential equations. These sets of equations are solved numerically using the Runge‐Kutta fourth‐order scheme followed by the shooting algorithm. The effects of physical parameters such as magnetic field, Prandtl number, Eckert number, Schmidt number, unsteadiness parameter, and chemical reaction parameters have been discussed on velocity, temperature, and concentration fields. Computation for the coefficient of skin friction, rate of heat and mass transfer is done and presented in a table for validation of the present outcomes.     

Comparative analysis of a Sisko nanofluid over a stretching cylinder through a porous medium

The present article examines the Sisko nanofluid flow and heat transfer through a porous medium due to a stretching cylinder using Buongiorno's model for nanofluids. Suitable similarity transformations are used to transform the governing boundary layer equations of fluid flow into nonlinear ordinary differential equations. The finite difference method is used to solve coupled nonlinear differential equations with MATLAB software. The impact of different parameters viz., the Sisko material parameter, porosity parameter, curvature parameter, thermophoresis parameter, and Brownian diffusion parameter on the velocity and temperature distribution are presented graphically. Moreover, the effect of the involved parameters on the heat transfer rate is also studied and presented through table values. It is noticed from the numerical values that the porosity parameter reduces the velocity while enhancing the temperature. The curvature parameter enhances the velocity throughout the fluid regime and reduces the temperature near the surface while enhancing the temperature far away from the surface. The study reveals that the thermophoresis and Brownian diffusion parameters that characterize the nanofluid flow reduce the wall heat transfer rate, while the curvature parameter enhances it. This investigation of wall heating/cooling has essential applications in solar porous water absorber systems, chemical engineering, metallurgy, material processing, and so forth.     

年处理100万t中低品位磷矿高效清洁生产工艺

中低品位磷矿高效清洁综合利用是中国基础磷化工产业发展中遇到的共性瓶颈问题。以中低品位磷矿磷-钙-镁一体化综合利用中试成果为基础,通过创新集成技术对中低品位磷矿直接进行处理,获得高品质磷精矿[w（P₂O₅）≥36%、w（MgO）≤0.5%]可用于任何湿法磷酸及热法黄磷生产工艺,同时回收高附加值的氢氧化镁和轻质碳酸钙。该工艺磷全部回收、无尾矿产生、实现了废水近零排放,项目的实施对推动中国磷化工产业可持续发展及从源头解决“三磷”问题具有重要意义。     

Performance assessment of food safety management systems in animal-based food companies in view of their context characteristics: A European study

Recurrently the question arises if efforts in food safety management system (FSMS) have resulted in effective systems in animal-based food production systems. The aim of this study was to gain an insight in the performance of FSMS in European animal-based food production companies in view of their typical context characteristics. Hundred European companies (from Belgium, Spain, The Netherlands, Greece, Italy, and Hungary) varying in company size, and producing different types of fresh and processed animal-derived products (dairy, beef/lamb, poultry, and pork) were assed using a diagnostic instrument. Results indicated that most participating companies adapted adequately their food safety management systems to the riskiness of their context characteristics resulting in rather good safety output scores. Only a small group have overall basic systems and operate in a moderate or moderate-high risk context, which was reflected in lower safety output scores. Companies tend to invest first in the control strategies whereas assurance activities such as verification and validation seem to require more time and effort to achieve advanced levels. Our study demonstrated that also small and medium enterprises managed to have advanced systems, and achieve a good safety output. However, their typical organisational characteristics such as less resources (educated staff, laboratory facilities, time), more restricted formalisation (restricted use of procedures and formal meetings), limited information systems, but more stable workforce, might require more tailored support from government and/or branch organisations to develop towards advanced systems in the case of high-risk products and processes. More in-depth studies to successful SMEs could give insight in best practices to improve FSMS performance.     

基于源质的煤基中间相小球体生成与可控演化

煤全组分族分离所得的密中质组是中间相小球体生成的来源物质（即源质）。以该源质为原料，制备煤基碳质中间相。考察了炭化过程中温度、恒温时间、氮气流速、原料进样方式和添加剂等因素对中间相小球体生成过程的影响，探讨了中间相小球体演化过程的可控性。结果表明：温度、恒温时间、进样方式是影响中间相小球体生成的主要因素，能够控制生成中间相小球体粒径大小；温度升高或恒温时间延长均会加剧原料分子的热反应，促进中间相小球体的生成和融并；大面积的融并将使粒度迅速增加，部分球体解体，球体数目下降，最终形成体中间相；进样方式主要通过影响小球体演化过程中挥发性气体的逸出及原料颗粒间热传递效率影响小球体的生成和发展；氮气流速起到辅助调控作用；添加剂的加入促进了原料成核，加速了小球体的生成。     

Facile synthesis of polyoxometalate-based composite with doped ternary NiCoFe cations as electrocatalyst for oxygen evolution reaction

The construction of efficient and low-cost electrocatalysts for oxygen evolution reactions (OER) to replace precious catalysts is a necessity to achieve economic production of hydrogen. Herein, we report an efficient tri-metallic electrocatalysts for the OER that is prepared by incorporate nickel, cobalt and iron cations on Triton X-100/phosphotungstic acid organic-inorganic composite without utilize any binders or energy consumer procedure. Considering to the synergy effect of simultaneous absorption of NiCoFe cations on composite substrate, the as-made tri-metallic catalyst exhibits excellent OER activity with a small overpotential of 210 and 330 mV at a current density of 10 and 100 mA cm^?2, respectively. Moreover, remarkable trends in electrocatalytic activity of mono-, bi- and tri-metallic electrocatalysts at low (10 mA) and high (100 mA) current density are observed. In addition, this new families of non-precious metal catalyst shows long-term durability in 1 M KOH.     

Permittivity of polycrystal: Laminar structure

A simple model of the laminar polycrystal is constructed that can be solved analytically and it also provides various mixing formulas. The polycrystal structure is composed of the layers, which represent rotated anisotropic crystallites. The dielectric response of such structure is much more complex comparing with the response of the layered structure built up of the isotropic materials. The general formal expressions for the effective permittivity were derived. The micro-geometry is determined by the distribution function of the crystal orientations. The effective permittivity can be controlled by variation of the distribution function. By discussing three examples it was shown that the uniform distribution of 2D rotations, as well as uniform 3D rotations, leads to the logarithmic-like mixing law of the effective permittivity.     

中低温煤焦油基炭微球的制备

通过馏分切割、温和加氢相结合对中低温煤焦油进行精制处理，精制后的原料采用分级热聚制备中间相炭微球。考察了精制处理条件对原料性质、中间相炭微球宏观外貌及微晶结构的影响。采用FTIR、GC-MS、族组成、元素分析对原料进行表征，采用SEM、XRD对中间相炭微球进行表征。结果表明：中低温煤焦油中300～430℃馏分油是制备中间相炭微球的较佳馏分。300～430℃馏分油中正庚烷可溶物（HS）质量分数高达84.76%，吡啶不溶物（PI）质量分数低至0.23%，杂原子含量低，芳烃化合物的环数为2～4环。300～430℃馏分油在T_H=350℃、p=8MPa、t=1.5h、剂油比1∶40（质量比）的条件下温和加氢得到的精制原料，经420℃热聚6h得制备的中间相炭微球宏观外貌、微晶结构较好。中低温煤焦油基炭微球的粒径范围为5～15μm，小球表面光滑，微观结构为地球仪型，经1450℃高温煅烧后，石墨化度达到12.33%。     

LD27-2油田稠油油藏蒸汽吞吐中后期注采参数优化研究

蒸汽吞吐是稠油油藏开发的最有效措施之一，但是对于海上油田的特殊条件，在进行蒸汽吞吐3~4轮后，即意味着进入蒸汽吞吐中后期。此时，如何调整注采参数，是海上稠油油藏高效开发的关键。针对LD27-2油田稠油油藏的开发特点，在地质建模和高度历史拟合的情况下，对LD27-2油田稠油油藏开发状况进行多轮次预测；基于生产历史拟合的油藏数值模型，开展了不同蒸汽干度、注汽强度、注汽强度递增等条件下A22H井和A23H井蒸汽吞吐至开采至10年的油藏数值模拟，明确不同注采参数的影响规律，优化了LD27-2油田稠油油藏蒸汽吞吐中后期注采参数。